Bissell is some of the favorite brands for vacuum cleaners thanks to its powerful and reliable technology as well as a variety of models that suit every household.
However, like any other vacuum cleaners, even the best ones can sometimes underperform. Perhaps one of the most common problems with Bissell vacuum cleaners is their loss of suction. Read Here: 10 Best Vacuum for Hardwood Floors and Carpet
Whether your Bissell vacuum cleaner’s suction power is lagging or your vacuum is not picking anything at all, there are a few hand-on maintenances on how to fix Bissell vacuum suction.
1) Emptying the Dirt Bag
The first place you need to look for on how to fix Bissell vacuum suction is the dirtbag. When the dirtbag is full, or it has become torn or ripped, then there will be a corresponding loss of suction.
AS you clean, dirt accumulates in either the bag or the dirt canister, depending on the model of your Bissell vacuum.
For bagless Bissell vacuum cleaners, it is easier to monitor since the dust cup is usually translucent or transparent. Plus, there will be a Full or Max line engraved on the outside. We recommend that you empty out the dirt once it is about 50 percent full.
For bagged Bissell vacuum cleaners, some models will have a full bag indicator, letting you know when it is time to empty the dirtbag. To fix Bissell vacuum suction, you only need to remove the bag and get rid of the dust.
Whether bagged or bagless, make sure to clean the dirt canister or bag with warm water and soap, then air dry, before putting it back to prevent unpleasant odor.
Now, if you see holes or tears on the dirtbag, then you need to replace the bag immediately. Not only does it cause loss of suction but a tore dirtbag also scatters dust inside your vacuum cleaner which can damage its motor and engine.
2) Cleaning The Filters
Another way on how to fix Bissell Vacuum Suction is to clean its filters and making sure that they are not clogged. Most Bissell vacuum cleaners have two filters. A pre-motor filter to keep the dust out of the motor and an exhaust filter. These filters may
have a plastic frame surrounding a sheet of material or something like a box container holding a sponge type of HEPA filter.
Most filters are washable but check with the product description or the manual to be sure. If washable, you only need to rinse the filters under cold running water and leave them to air dry for a few hours.
After that, you can insert them back into place and the suction power should return to normal.
However, if you see a damaged filter, then it is time that you replace your filters. Your manual should also indicate how often the filters need to be washed or replaced.
3) Damaged or Clogged Vacuum Airflow
If your Bissell suction is still not working properly, then perhaps there’s an obstruction in your vacuum cleaner’s hose. Stretch out the hose to full length and insert a stick or broom handle through it.
This should help push any obstruction all the way through. After that, inspect the hose from end to end and see if there’s any hole, crack, or kink that’s causing the vacuum to lose suction.
If the hose is damaged or compromised, then it needs to be replaced. A loose or bad connection also causes loss in suction so make sure that the hose is properly connected to the vacuum cleaner.
4) Check The Rotating Brush
If the beater bar or rotating brush of your Bissell vacuum is not turning, then there is a loss in suction. The brush roll sweeps debris and dirt into the vacuum hose and making it easier for the vacuum to pick up dust and dirt.
Now, if the rotating brush is not working, then there will be a corresponding loss of suction power.
Just remove the brush roll from the floor head and remove anything that is causing the blockage. Cut hairs or larger debris with scissors and remove them by hand. After that, you can clean the brush roll and allow it to air dry. Attach it back to the vacuum cleaner and see if it fixes the suction power.
However, if the blockages end up damaging the drive belt that turns the brush roll, then it may be broken and should be replaced in order to regain proper suction.
5) Motor Damage
Lastly, if you already did the above steps on how to fix Bissell vacuum suction and failed, then there could be a bigger problem.
The vacuum’s motor or some parts of the motor could be damaged. A bad motor can sound off-key, it will run in fits and starts or even produce smoke.
Motors are not general DIY jobs and should be left to a professional.
On some Bissell vacuum bags, the motor uses a spinning plastic fan blade which produces suction. This fan blade is directly attached to the motor axle. Debris and dirt pass through the blades which are then pushed into the bag.
If any of these blades have been broken, the vacuum motor may run off-key or vibrate which causes loss of suction. If that’s the case, then you can just replace the fan blade.
Suction generated by a fan motor powers your Bissell vacuum cleaner as it pulls dirt through the hose and into the dirtbag or cup. Some Bissell vacuum cleaners will have a beater bar or rotating brush at the end of the nozzle that helps sweep and agitate dirt into the suction chambers.
All these parts need to be free of obstructions and cleaned properly in order for the vacuum cleaner to stay 100% functional. Otherwise, it will gradually lose suction. By following the above tips on how to fix Bissell vacuum suction, you can now again clean your home efficiently.
The post How to fix the loss of suction in a Bissell Vacuum appeared first on Relentless Home.
via Relentless Home https://relentlesshome.com/how-to-fix-the-loss-suction-bissell-vacuum/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-fix-the-loss-suction-bissell-vacuum
The floors are sparkling and the house looks clean. However, there’s still an unpleasant odor lingering around. Think you need to clean the second time around?
Hold your horses!
There has to be an easier way to find that smelly source.
Assuming that you’ve already taken care of the garbage and there are no hidden spots for you to clean, then there is a good chance that the odor comes from a cleaning tool.
Perhaps your vacuum cleaner?
You see, keeping your living space nice and clean is a normal routine, but not everyone thinks about cleaning the machine that does it all.
Vacuum cleaners remove dirt from your home. If not cleaned properly, that dirt accumulates, producing an unpleasant odor as you are using the machine. Read More: How to Unclog a Vacuum Cleaner?
Fortunately, a stinky vacuum cleaner can smell fresh again. Here’s a guide on how to fix a smelly vacuum.
How To Fix A Smelly Vacuum: 4Methods To Try
1) Emptying the Dust Bin or Bag
If your vacuum cleaner comes with a dust bag, then there’s a high chance that it could be the source of that unpleasant smell. Remove the bin or bag and empty its content into the garbage.
Then wash it thoroughly with soap and hot water. We highly recommend that you add a small amount of baking soda or white vinegar in order to kill potential fungus and mildew. Make sure that every angle and corner is washed.
Let it sit to dry before you put it back and use the vacuum cleaner again.
2) Replacing or Cleaning The Filters
Over time, the vacuum cleaner filter starts to get dusty and dirty which causes odor. If you have a washable filter, simply remove the filter from the machine and rinse it under cold water. You can rinse the filter until the water runs clear.
You should know that even clean-looking filters can accumulate an impressive amount of dirt and dust. So, do not be surprised if this process takes a few minutes. After that, you can air-dry the filter for the whole day before placing it back to the machine.
Now, if the filter is not washable, then it might be time for you to replace it. In general, vacuum filters need to be replaced at least once a year. If you own pets or heavily use the vacuum cleaner, then it should be checked and replaced every 6 months.
2) Washing The Hose
The vacuum hose is another main culprit when it comes to smelly vacuum cleaners. This is because it is one of the first places that dust and dirt pass through before reaching the filter, dust bin, or bag.
In addition, small particles can often get stuck within the inner tube layer, which causes the hose to be clogged. Over time these clogging causes decay and create a strong unpleasant smell.
Fortunately, cleaning a hose is rather simple.
First, you need to detach the vacuum hose and take it outside. In order to remove any clogging, you can use the stick of a broom, a straightened coat hanger, or any other straight tools. Push through until the blockage inside is released.
After removing the blockage, pour at least 4 inches of hot water into a sink. Add 1 tablespoon of regular dish soap and 2 tablespoons of bleach, vinegar, or baking soda. Place the hose in the sink.
Move the tube and make sure that the water runs through and over the entire area of the tube. You can also use a stick with fabric at the end to clean the inside of the hose.
After that, place the hose under the tap and allow water to run through the hose. Allow it to dry before attaching it back to the vacuum cleaner.
4) Checking the Brushes
The rotating brushes should be maintained and cleared at least 1 – 2 times a year, whether it starts to smell or not. Brushes are often used to clean rugs and carpets; thus, they can accumulate a large amount of dust and dirt on their own.
And if you have naughty pets in the house, you might be using the vacuum cleaner to clean off residues of their accidents, further causing that unpleasant odor on the brushes.
Thus, having a quick look under the floor head attachment can be helpful. First, make sure that the vacuum cleaner is unplugged. If the brush is removable, you can detach it from the floor head attachment. Using a
pair of scissors, cut and remove any hair stuck within the bristles. Just be careful not to cut the bristles.
Once you removed every strand of hair, you can now wash the brush with soap and water. Or if it is not removable, you can just spray vinegar and water.
Air-dry the brush for a few hours or place it back only when fully dried.
Preventing The Bad Odors From Coming Back
Now that you know how to fix a smelly vacuum, it is time to learn how to keep it smelling fresh.
Probably the most common household cleaning item used, baking soda can absorb any unpleasant odor. And you can use it to keep your vacuum cleaner smelling nice and fresh. Just sprinkle a few teaspoons of baking soda inside the dust bag or bin.
If you would like to use a spice from your kitchen, then cinnamon is a great idea. Sprinkle half a tablespoon of cinnamon powder inside your dust bag or bin.
You can also add essential oils to keep your vacuum smelling nice and fresh. Thyme or lemongrass are beneficial since they are also great at fighting molds. You can add at least 30 drops of essential oils to a 32 ounces spray bottle then fill it with water and a teaspoon of baking soda.
Spray this solution to the inside of the bin or bag. Don’t dampen the area too much.
Whether you are sprinkling baking soda or commercial deodorants on your vacuum cleaner, cleaning it should not be optional.
Regular cleaning is the most effective method on how to fix a smelly vacuum. Depending on how often you use the vacuum cleaner, it is recommended that you thoroughly clean it every 3 – 6 months. Now, if you have a pet, then you need to clean your vacuum cleaner every other month.
The post Does Your Vacuum STINK? How to fix a smelly vacuum appeared first on Relentless Home.
via Relentless Home https://relentlesshome.com/how-to-fix-smelly-vacuum/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-fix-smelly-vacuum
Most, if not all people can attest that HEPA vacuum cleaners are amongst the most efficient cleaners out there. Having a HEPA filter in your vacuum cleaner can prove beneficial, particularly if you or a family member suffers from asthma or allergies.
Symptoms like runny nose, watery eyes, and continuous sneezing will become a thing of the past. In this article, we’ll discuss the HEPA filter and its benefits along with tips on how often a HEPA filter should be changed.
HEPA Filter: How Does It Work?
Short for High-Efficiency Particulate Air, HEPA filters are highly effective at sucking micro-particles, down to 0.3 microns in size, out of the air. The filter itself is constructed from fiberglass fibers which are randomly arranged to trap both small and large particles. Read Here: How to Unclog a Vacuum Cleaner?
HEPA vacuums can trap even the smallest particles since the air is being forced through a fine mesh with any particles clinging to the fibers within the filter.
Benefits of a HEPA Filter
1) High Air Quality Indoors
If you’re currently using HEPA vacuums, then you’ll definitely see a huge improvement in the quality of your indoor air. The vacuum should suck in every particle with the HEPA filter preventing any impurities and contaminants from being released back into the airflow.
2) Prevent Asthma and Allergy Flare-Ups
HEPA filters are able to get rid of pollutants from the air which causes asthma and allergy flare-ups. It is particularly useful during the summer months when hay fever is as its most prominent since it can easily pick up the smallest pollen particles and stop them from being released back into the air.
3) Peace of Mind
There’s no greater peace of mind, knowing that you’re residing in a clean home and breathing clear and safe air. Using vacuum cleaners with HEPA filters, you ensure that you and your family members can breathe easy.
How Often A HEPA Filter Should Be Changed
AS you can see HEPA filters can go a long way to protecting the air quality indoors. Unfortunately, HEPA filters are not foolproof and require replacement over time, ensuring that your vacuum cleaner operates at optimum performance.
Changing the HEPA filter is quite beneficial in so many ways. For starters, it allows your vacuum cleaner to clean your house to the highest filtration possible cleaning the air inside your home. Secondly, efficient HEPA filter is crucial to your family’s health. Lastly, changing the HEPA filter as needed can help extend the longevity of your vacuum cleaner and ensuring that it runs at an optimum level.
But, since HEPA filters are built to last for a really long time, it can be easy to forget about them and when you should replace them.
Knowing when and how often a HEPA filter should be changed is largely a case-to-case basis, depending on the level of use, the quality of the indoor environment, the condition that the vacuum cleaner works in and so much more.
Still, here is a general guideline on how often a HEPA filter should be changed.
If you’re using your HEPA vacuum in a strictly residential setting, then the filter could last you at least 2 – 3 years before they need to replace it.
It still depends on how much you use the vacuum cleaner and how big your home is, however, regular use based on the average cleaning schedule should keep the filter doing its job for at least 24 – 36 months.
Now, if you’re using the HEPA vacuum in a commercial setting, the HEPA filter needs to be changed much more frequently than once every 2 – 3 years. Read here: Riccar Vacuum Reviews: Top 3 Picks in 2020
If it’s used in the workplace daily, then you need to check the filter every 6 months. If the filter looks soiled, then it needs to be changed. Otherwise, you can change the HEPA filter at least once a year.
The Musty Smell
It is good to know just how long a HEPA filter can last. However, one tell-tale signs that it is time to replace the filter is when you notice a musty smell when using the vacuum cleaner. There’s a good chance that the HEPA filter is no longer working effectively and should be changed right away.
The smell test can indicate that it’s time to replace the HEPA filter before 2 – 3 years for residential use and before the year in commercial settings.
Don’t Forget Other Filters
There is some HEPA filtration system having an extra layer of filtration— the carbon pre-filter. They are a great option for removing odors in the air and just like HEPA filters, these carbon filters should also be changed once every 2 – 3 years in a residential setting and once a year for commercial use.
In addition, other pre-filters are designed to capture the larger particulate matters. These filters will need to be checked every 3 – 4 months and should be changed if they look too soiled.
Also, if the housing that holds the filter or the filter itself looks damaged, then you need to change the filter as well.
Whether you suffer from asthma or allergies, or you just want to rid your home of small particulate and air pollutant, then getting a vacuum cleaner with a built-in HEPA filter is a good investment.
However, you also need to ensure that the HEPA filter is working at its maximum capacity. After some time, you will need to replace it altogether in order to ensure that your home will have safer and cleaner air to breathe.
via Relentless Home https://relentlesshome.com/how-often-change-hepa-filter/?utm_source=rss&utm_medium=rss&utm_campaign=how-often-change-hepa-filter
Household chores can be cumbersome. Cleaning every corner of the house is no fun at all.
However, with the increasing amount of pollution, it is crucial that you take the right steps in keeping your home clean, especially the carpets, furniture and the curtains, which tend to accumulate a lot of pet hair, dust mites, dander, and other allergens.
The only way to remove these is with a handy vacuum cleaner. If you do not like the bulky and rugged bagged vacuum cleaners, then you can always go with the cordless one like the Dyson V10 or V11. Read Here: How to Unclog a Vacuum Cleaner?
However, to make sure that your home stays dust and germ-free, you will also need to know how to clean a Dyson cordless vacuum.
Here is a guide on how to clean a Dyson cordless vacuum as well as some maintenance tips.
1) Emptying and Cleaning The Dirt Bin
To ensure optimum performance of the Dyson vacuum cleaner, you need to empty the dirt bun as soon as dust and dirt reach the level of the Max mark. Don’t overfill.
Here’s how to clean a Dyson cordless vacuum dirt bin.
Disconnect it from the charger and be careful not to switch the “ON” trigger.
Remove the wand— press the red wand release button and pull away from the bin. To release the dirt, you need to hold the vacuum with the bin in a downward position. Then push the red bin release button, the bin should slide down and cleaning the dirt as it goes.
In order to minimize allergen or dust contact when emptying, tightly encase the clear bin in the plastic bag and empty it.
Once the dirt is removed, it is time to clean the dirt bin using a damp cloth only. Before attaching it back to the machine, make sure that the bin and seals are dry.
2) Cleaning The Brush Bar
The Dyson V10 and V11 Cordless Vacuum Cleaners have 2 washable brush bars you need to check and clean regularly.
Here are the steps on how to clean a Dyson cordless vacuum brush bar:
3) Washing The Filter
To wash the filter unit of the Dyson cordless vacuum you need to remove it by twisting it counter clockwise, pulling it away from the main body.
Here are steps on how to clean a Dyson cordless vacuum filter unit:
It is recommended to check and wash the filter unit at least once every month.
4) Removing Blockages
The Dyson V11 and V10 Cordless Vacuum cleaners are fully equipped with automatic cut-out. So, if any part of the vacuum gets blocked, the blockage indicator LED illuminates.
To remove the blockages, allow the appliance to could down first. Make sure that it is not connected to the charging port.
Detach the cleaning wand. Using a flashlight, look inside the tube. Push the blockages out using a straightened coat hanger or the stick of the broom.
In addition, you can also clean the wand with running water and soap.
Leave it to dry before attaching it to the machine and using the vacuum cleaner.
Turn off the vacuum cleaner. Place it on the docking station. After that, plug in the docking station and turn it on to charge the vacuum cleaner.
Take note that the vacuum cleaner needs to be fully charged before the first use. Recharging can take up to 3.5 hours.
Use only Dyson chargers to charge your Dyson V10 and V11 cordless vacuum cleaners. Also, use only Dyson batteries since other types of batteries can burst to cause damage and injury to persons.
2) Vacuuming Properly
Here are some tips on how to use the Dyson Cordless Vacuum Cleaners properly:
The post How to Clean and Maintain the Dyson V11 and v10 Cordless Vacuum appeared first on Relentless Home.
via Relentless Home https://relentlesshome.com/how-to-clean-dyson-cordless-vacuum/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-clean-dyson-cordless-vacuum
Your vacuum cleaner helps in keeping your home smelling nice and fresh by getting rid of dust, dirt, dander, and other particles stuck on your floor and in your carpet and upholstery.
However, since they suck in all the dirt, they become the new hub of all those dust and germs from all over your home. And if you don’t regularly maintain it, that cleaning machine can start to contribute to the mess in your home, emitting a nasty smell. Read here: 10 Best Vacuum Cleaners Under $300
In this article, we will show you the main causes of smelly vacuums as well as steps on how to make your vacuum smell good again!
4 Causes of a Smelly Vacuum
1) Pet Hair
If you have fur babies around, their coat and hair might be the main cause of a smelly vacuum. Pet dander and hair are already smelly and when you vacuum them, they will carry the odor inside the device.
Not only that, but pet urine can also add a stronger stench. Although it is unlikely that you will vacuum your pet’s accident directly, the liquid can stick to dust and pet hair. Once vacuumed, this combination of pet hair and dried urine can create the best recipe for a nasty, musty smell.
2) Mold Accumulations
Don’t have any pets? You’re still not exempted from smelly vacuum cleaners.
Mold particles are usually found in vacuum filters and bags. If left unattended, this can create a strong smell that you might be quite familiar with (the strong musty smell in the basement).
Mold loves humidity and moisture to grow. Now, if you tried to vacuum a wet carpet or cleaned the vacuum bag with water then used it before allowing it to dry, then you are welcoming mold into your vacuum cleaner.
3) Excessive Dust
You don’t just vacuum dust. When vacuuming, dirt and other pieces of debris also join the ride. Whether you are catching used coffee grinds or dried food mess, they all contribute to a strong, smelly vacuum.
In addition, letting too much dirt and dust accumulate in the dust bin or dust bag can eventually impact the life of your vacuum cleaner.
4) Burnt Belt
The vacuum belt may also cause a foul odor. Made of rubber, belt allows the brush to roll, capturing dirt, hair, and dust. Without proper caring and maintenance, the dirt and hair stuck within the brush bristles can prevent the brush from rotating properly which damages the rubber.
Also, the belt can get caught on the brush as well. Overused and stretched belts produce a burning plastic smell.
How To Make Your Vacuum Smell Good
1) Cleaning The Dust Bag
The first tip on how to make your vacuum smell good is to always clean the dust bag or dirt canister. Always dispose of accumulated dirt on the canister or bag before it is even full.
After that, do it a habit to always clean your dust bag or canister with freshwater or as per the manufacturer’s instruction. Just make sure that the bag or canister is completely dry before putting it back to the vacuum cleaner.
2) Cleaning The Filter
Vacuum filters are the ones keeping dirt, allergens, and dust out of the air. Thus, they too can become soiled and dirty. It is recommended that you clean your filter as per your manufacturer’s instructions.
Or if it is too soiled, then it is recommended that you replace it to keep your vacuum cleaner in optimal shape and increase the filtering efficiency. In general, it is recommended that you change your vacuum filter every 3 – 6 months.
3) Cleaning The Hose
Another way on how to make your vacuum smell good is to clean the vacuum hose or tube. This is one of the first places where dirt and dust pass through before reaching the vacuum’s filter, dust bag, or dirt canister.
Furthermore, small particles usually get stuck within the inner tube or hose, causing a clogged hose. Over time such clogging can cause decay, creating an unpleasant odor.
To prevent this, you just need to remove any clogging and cleaning the hose with water or liquid soap or as per manufacturer’s instruction.
4) Cleaning The Brushes
The vacuum’s rotating brushes need to be maintained and cleaned at least once or twice a year. They are often used to clean carpets and rugs, accumulating a large amount of dirt and dust on their own.
To clean the brush, you just need to cut and remove and hair stuck within its bristles. After that, pull out strands of hair as well as dirt. Wash the brush with soapy water or as per manufacturer’s instruction. Read Here: Shark Vacuum Not Sucking – How To Fix It
5) Using Perfume Pads
For the more personal approach on how to make your vacuum smell good, there are perfume pads available in various sizes and aromas.
Check the accessibility and size of your vacuum filter before you choose the perfume pad. In most cases, perfume pads can be inserted into the vacuum filter.
The purpose of these perfume pads is to release the aroma into the air whenever you use the vacuum cleaner.
6) Sprinkling Baking Soda or Cinnamon
If you just want to neutralize the smell from your vacuum cleaner, you can sprinkle a teaspoon of baking soda into your vacuum dust bag or dirt canister. Baking soda prevents bad smells from coming back out to your home.
Or you can also sprinkle a small amount of powdered cinnamon to counteract the smell of dust and dirt that the vacuum picks up while providing a fresh, sweet scent. If you don’t like cinnamon, you can try other items such as dried orange rind or coffee beans to pre-fill your vacuum dust bag or dirt canister and provide some level of odor protection.
Make it a habit to sprinkle cinnamon and baking soda or other odor-protecting items to your vacuum bag every time you change or clean it for the best results.
Cleaning It Off
When used regularly, vacuum cleaners will start producing an unpleasant odor. We hope these tricks can help keep your vacuum in good condition and always smelling fresh, so you and your family can enjoy a clean and safe environment to live in.
via Vacuum Cleaners https://relentlesshome.com/how-to-make-your-vacuum-smell-good/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-make-your-vacuum-smell-good
For your vacuum cleaner’s performance to be up the mark, the engine or pump needs to be working efficiently.
The pump has moving parts which tend to fail overtime as a result of normal aging or wear and tear. Here’s a guide on how to repair your vacuum cleaner engine.
Covering The Basic
Before we teach you how to repair your vacuum cleaner engine, first you need to know how a vacuum works and a few basic things you will need to repair the engine or pump.
The vacuum cleaner has a fan where a motor is attached. When the fan rotates, suction is created, pulling in the polluted air as well as debris and dirt. Then, a porous bag in the vacuum cleaner filters out the dirt-filled air stream. Read More: Shark vs Dyson Vacuum Comparison
Now, to repair your vacuum cleaner engine, you will need to use pliers and screwdrivers.
Start by removing the handles, getting rid of filters, and taking out the switch assembly. Be careful not to disturb the electrical connector which is typically underneath the switch assembly.
Remove the vacuum case that’s protecting the interior in order to access the core engine. This is much easier if you unscrew the neighboring motherboard so it can move freely and you get to work where needed, instead of removing it completely since you will have to rewire everything back which can be tricky if you have no experience.
In most vacuum cleaners, it’s not necessary to remove any rubber bumpers surrounding the cord wires or machine.
You need to be gentle in removing the parts as the little pieces and bits are fragile. Also, remember where all items were previously positioned, more importantly, the screws.
Now that you’ve released the vacuum cleaner’s pump cabinet, take the motor out of the vacuum. Some models will have a motor chamber that contains all motor assembly while others only have a motor shell.
2) Cleaning and Fixing Engine Parts
At the end of the motor, you’ll see a metal shield. Tap it lightly to expose the blower fan. Remove the nut holding the fan in its position. This should allow you to remove the flat spacer washer and the aluminum blower.
Gently lift the carbon motor brushes out. These are typically held in place with the spade connectors so you can seamlessly pull them out directly. The motor brushes should look solid and long.
From there, you should see 2 types of housing— the stator housing which holds that female spade socket and the brass housing which holds the male spade connector.
Once the brushes are removed, you can clean them with the electrical cleaner or replace them altogether to get the best out of your vacuum cleaner.
If you decide to replace the brushes, always replace both of them at the same time.
After the brushes, you can now remove the vacuum engine stator by pressing down on the metal spring clip which fastens it in place. The stator should slide out easily.
There should be an electronic controller attached to the stator. You should clean up any dust or dirt residue on the inside of the stator and its housing, contributing to the optimum performance of your vacuum cleaner.
After the stator, you’ll have to carefully pull out the rotor. It should have bearing on either end in addition to the lower bearing that’s pressed into the housing which you also need to pull out carefully. Make sure not to lose the flat small spring washer and that the rotor should be removed in one piece.
You might also notice the commutator found at the end of the rotor. These are rings of copper strip which can be super dirty, which are the common cause of faulty vacuum cleaner engines. To fix this issue, you need to mount the rotor in a mini lathe (if you have one). Using wet and dry fine sandpaper, sand down the end of the commutator.
The commutator doesn’t need to be perfectly smooth and should operate just fine if there are a few small scores present. Use only feather-like strokes in order to sand down the commutator and be careful not to sand a lot away.
Next is the aluminum blower that will most likely be clogged with dust. You need to unclog it to improve the overall functioning of the vacuum cleaner. One swift push around some fins with long cable tie should do the trick in addition to an electric cleaner.
3) Repairing The Electronic Gears
To repair your vacuum cleaner engine electronics, you need to be extremely careful since there will not be much that’s attached as well as a few loose main connections will be exposed.
The electronic structure of the engine is simple, containing the thermal cutout of the device as well as a triac with 20 – 30 amp. Ensure that all the triac wires are connected to the body. Also, ensure that all parts of the plastic clips holding the connectors together are not compromised, wrapping the connector in electrical tape to securely hold it together.
See if the fuse is intact, otherwise, you need to replace the fuse and check to see if the connections in the plugs are okay.
Once you’re done with all the cleaning and repairing, it is time to re-assemble the engine.
Make sure that all parts are completely dry before reassembling since you don’t want to risk short circuitry.
Restore all the pieces and screws back to their rightful places and take your time while doing it. Double-check to confirm that everything is back in place and that all wiring is intact. Read Here: How to Unclog a Vacuum Cleaner?
After reassembling, plug the vacuum cleaner to an outlet and turn it on. It should be able to function properly and correctly unless you made some mistake during the repairing and reassembling process.
In such a case, you’ll need to disassemble it once again or take the vacuum cleaner to a qualified professional in order to repair your vacuum cleaner engine.
via Vacuum Cleaners https://relentlesshome.com/how-to-repair-the-engine-pump-vacuum/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-repair-the-engine-pump-vacuum
Vacuum cleaners— what would we do without them? One of the best and high-end manufacturers of powerful vacuum cleaners is Shark.
However, regardless of how high-end your vacuum cleaner is, it can be worthless over time if you do not ensure proper maintenance. Stop for a moment and think about what a vacuum cleaner does for you.
It absorbs and sucks a large volume of dirt, debris, dust, pet dander, and small particles that would otherwise make your home very dirty. Such accumulation gives your vacuum cleaner prone to clogging or losing its efficiency. Read Here: Shark Vacuum Won’t Turn On – How To Fix It
One of the most common things you can do to increase your Shark vacuum’s lifespan and efficiency is regularly emptying and cleaning its dirt bin.
Considering the importance, in this article, we’re going to explain when and how to empty Shark Vacuum cleaners.
When To Empty And Clean Shark Vacuum Cleaners?
This will depend on how frequently the user uses the Shark vacuum cleaner as well as how clean or dusty your home can be. So, it wouldn’t be useful to tell you to empty your vacuum cleaner on a monthly or weekly basis.
However, a useful feature of the Shark vacuum cleaner is that they have an indicator when it is time to empty the dirt bin. Check the label for the indicator light, usually turning red when it has reached the maximum level of accumulated dirt or dust.
For the cordless Shark vacuum cleaner, it features clear or transparent dirt canister with lines, so you can better see when it’s time to empty the canister.
Now, if you have one of the old models without an indicator, then there are signs that will tell you when the dirtbag is already full and it is time to empty the vacuum cleaner:
How To Empty Shark Vacuum?
1) Unplug the Device
First off, you need to ensure that the Shark vacuum cleaner is disconnected or unplugged from the outlet. If you have the Cordless Shark vacuum cleaners, then make sure to remove the battery. After that, find a spacious place for cleaning and emptying the vacuum cleaner.
2) Opening The Device
The opening features of Shark vacuum cleaners may vary by model. In general, you only need to open the bin, hold the handle that is adjacent to the bin, and grasping it open.
3) Separating the Dust Container
Once you opened your device, you should be able to see the dirt bin or dust container. Remove it from the device.
4) Removing the Pre-Motor Filters
Most Shark vacuum cleaners will come with pre-motor filters. Since they’re already out, perhaps you’d also like to clean them up to further optimize the performance of your vacuum cleaner.
If you’re unsure of how to clean the filter, check for the user’s manual.
5) Emptying The Canister
After removing the filter, you need to pull out the bin. Press the button near the bin, then using the handle, pull it out from the device. Empty the debris and dust into the trash can.
After that, you can use clean water in order to remove all sorts of dirt and dust from the canister and its filtration system. Make sure to rinse it by putting it under running water.
After cleaning the canister and its filtration system, allow it to air dry for at least 24 hours.
Do not try to put the dust container and filtration system back into the vacuum cleaner while wet. Otherwise, mold and mildew can grow and cause strong musty odor when using the vacuum cleaner.
Once dry, you can finally put it back into the vacuum cleaner.
Tips For Cleaning Different Shark Vacuum Models
As there are a wide variety of Shark vacuum models, the procedure for cleaning can vary from one another. Thus, you may need to pay closer attention to what you use and how to properly empty and clean the parts of your device. Read Here: 10 Best Vacuum for Hardwood Floors and Carpet
Here are a few tips on how to empty Shark vacuum of varying models:
To empty this Shark model, you need to start by sliding the dirt cup release tab at the top of the cup itself. Hold it over the trash bin and release the dirt. In order to open the dust cup, simply press the lower release tab.
In order to make sure that all debris and dirt have been emptied, open the dust cap from the top and press the upper release tab. Rotate it upside down over the trashcan. After that, place the dust cup back into position.
Separate the dirt cup from the rest of the device. You can press the dust cup release button or pull up the dust cup release latch which is usually located near the top of the cup, depending on the model.
Hold the dirt bin over the trash bin and press the bottom release button located at the front side to empty dirt. Ensure to close the dirt bin properly before placing it back into the device.
Separate the hand vac from the wand or separate the dirt bin from the hand vac. After that place, the dirt cup over the trash can and push the release button in order to empty debris and dirt. Put the dirt bin back into position.
Press the release button located near the want to remove the dust cup from the device. Empty it over the trash bin by pressing the lower release tab. There’s also a release tab on the upper part so you can hold the dirt bin upside down over the trash to empty the debris. Put the dust bin back onto the unit.
Separate the hand vac from the wand with the release button. Hold it over the trash bin and press the dust cup release button to empty the debris and dirt. Then, close the dirt bin and put the hand vac back to position
The post How To Empty Shark Vacuum -Step by Step Instruction appeared first on Vacuum Cleaners.
via Vacuum Cleaners https://relentlesshome.com/how-to-empty-shark-vacuum/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-empty-shark-vacuum
Having a clean home is a must. However, with your work and schedules getting in the way, it is no longer surprising if some people decide to use the modern approach in cleaning— the smart cleaning robots like the Shark Ion Robot.
Shark Ion Robot: What Is It?
Whenever you need a bit of cleaning but simply can’t because of work or other things you need to do, a robot vacuum cleaner will definitely save the day.
The Shark Ion Robot is the best solution for your daily problems in terms of home cleaning. This device features an easy-to-use mobile application that allows you to monitor and use the device anytime you want.
The Shark Ion Robot boasts a self-cleaning brush roll that collects hair, dust, allergens, and dirt to clean your home and prevent a daily build-up of this dirt in your home. It even features the Smart Sensor Navigation, allowing you to seamlessly navigate the floors and carpet while its proximity sensors continuously assess the surroundings to adapt to obstacles. Read Here: 10 Best Vacuum for Hardwood Floors and Carpet
Meanwhile, the dual spinning side brushes are also present, so it can clean out debris and dust from edges and corners Thanks to its Wi-Fi connectivity and optional cleaning scheduling, you should not have any trouble keeping your home clean every day.
While the Shark Ion Robot can be super effective in cleaning your home, sometimes, however, they also tend to have their mood swings, malfunctioning, or doing things they are not supposed to do.
And sometimes, the only thing you can do to ease their mood swings is by resetting them back to normal.
In that case, you might be wondering how to reset Shark Ion Robot.
Factory Reset: What Exactly Is It?
A factory reset is a useful troubleshooting feature that will send your Shark Ion robot back to its original factory settings. This means that it will delete all robot data including schedules, maps, Wi-Fi credentials, preferences, and settings.
When performing the factory reset from the Shark Ion Robot app, which is always recommended, the action will also remove the device from the app, returning all language selections, time-zones, cleaning preferences to their default state. Read Here: 10 Best Vacuum Cleaners Under $300
Not only that, but it also disassociates the device and any of its save data from your app account and removes any current 3rd party Smart Speaker connection.
However, if the factory reset is performed from the device itself, app data, cloud data, and all its account associations will stay intact.
Reasons To Do A Factory Reset
A factory reset of the Shark Ion Robot is usually recommended in the following scenarios:
1) Vacuum Not Connecting To The Wi-Fi
If you have a newly-bought Shark Ion Robot, then it might take a lot of tries before you can connect it to the internet successfully. You only need to make sure that you’re using the recommended frequency that your robot vacuum needs.
You can also try to reset your router to see if the device can connect. However, if you still can’t connect to the Wi-Fi network and could not find the reason why resetting the Shark Ion Robot can be your last resort troubleshooting step.
2) Software Issues
Like any other digital device out there, the Shark Ion Robot vacuum cleaner needs a software program in order to operate properly.
Now, if one day it does not work properly or seemingly spins around without ever cleaning at all, then it seems to be a software issue.
Such software issues include:
These signs could indicate that your robot is actually dealing with excessive data in its memory. In order to resolve this problem, it is recommended that you give your Shark Ion Robot vacuum cleaner a reset so that it can remove all unnecessary information that makes it struggle from its performance.
3) Re-selling The Shark Ion Robot
If you are planning to sell your Shark Ion Robot or transferring ownership of the robot to another user, then you will need to know how to reset Shark Ion Robot and resetting it to its default setting before turning it over to the new owner.
How to reset Shark Ion Robot
There are 2 main ways on how to reset Shark Ion Robot vacuum:
1) Factory Reset via the App
This is the most recommended way to factory reset your Shark Ion robot. AS mentioned above, this will remove the robot from the App as well as any saved data from the cloud.
You can use the following procedure to factory reset the Wi-Fi connected Shark Ion Robot:
2) Factory Reset via the Shark Ion Robot
If you can’t connect to the Wi-Fi network, then you will need to do a factory reset on the Shark Ion Robot itself. Fortunately, resetting the Shark Ion Robot is easy and simple.
Although a robot vacuum can help a lot in terms of cleaning your home, it can still malfunction like any device ever created. However, with the simple guide from above, you should be able to troubleshoot the problem and solve the issue, so you can make the most out of your Shark Ion Robot vacuum cleaner.
via Vacuum Cleaners https://relentlesshome.com/how-to-reset-shark-ion-robot/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-reset-shark-ion-robot
We all love our fur babies.
But, having pets at home has this one inevitability— urine everywhere. On walls, furniture, and their favorite spot— the cozy carpet.
There is no going around this unless you train your fur babies to do their business in a particular area— this will be a never-ending cycle.
So, when your pup positioned and peed on your new carpet, the key here is not only cleaning up his urine but also removing the odor. Because if you don’t, he’ll pick his scent and will take a piss on that one area all over again.
Think of it as marking territory.
He peed on it. It’s his.
A little animal psychology.
And in this article, we will show you how to get dog urine smell out of the carpet.
Pheromones and What Neutralizes it?
Dog urine contains pheromones. It is a part of a complex system that dogs use to communicate. These pheromones teach dogs respectable places and boundaries to urinate.
So, once your pup had an accident in the house, catching a whip of those pheromones can encourage him to urinate in that one spot again.
For you, you’d smell a foul odor caused by bacteria in the urine which produce ammonia. If you can’t see it, then using a blacklight or UV light can help you find it to ensure proper cleanup.
So how do you neutralize this smelly urine odor and its pheromones?
They destroy the enzymes and proteins that make up the pheromones in your pup’s urine. Not only can it help remove the smell, but it also reduces the chances of your pup being a repeat offender in that spot. Read Here: 10 Best Vacuum for Hardwood Floors and Carpet
However, there are also home ingredients that you can use on how to get dog urine smell out of the carpet.
Homemade Solutions For Urine Stain
For people who do not want to spend money on potentially harmful ready-made chemical items and want to go the DIY route, then here are some homemade solutions for urine stains you can try.
Vinegar + Baking Soda
Vinegar acts as the cleaner while baking soda helps absorb the stain.
To use this duo effectively, you need to pour the vinegar first then add the baking soda. If you do it baking soda first, you will have a bubbly mess in your hands.
Water + Vinegar + Baking Soda + Hydrogen Peroxide + Liquid Dishwashing Detergent
This is a 3-step solution.
First, you mix water and vinegar and treating the stained area with this mixture. Then you sprinkle baking soda over the affected area.
After that, a mixture of 1 teaspoon liquid detergent and 1 cup hydrogen peroxide is applied on the carpet, allowing it to dry.
How To Get Dog Urine Smell Out Of Carpet
1) Fresh Stains
When you caught your pup, doing something he shouldn’t be doing in your carpet, you need to make a firm “No” in a commanding voice, so that he will slowly learn that peeing on your carpet makes him a bad dog.
Then, quickly remove the fresh urine to lessen stain and odor afterward. To do this, use paper towels to absorb the urine. Stand on the pile of sheets, allowing it to absorb as much urine as possible. Do this until the area is dry.
Then use an enzyme cleaner to remove any lingering pheromones in the spot. If you do not have an enzyme cleaner, you can use clean water with homemade solutions, then blotting it dry afterward.
Then, use a wet/dry vacuum cleaner to clean up all dirty baking soda residues.
Take the urine-soaked paper towels into your pup’s designated bathroom zone or pee zone so that they are more inclined to do their business there.
Wait, can’t I use a towel instead?
Sure, you can. However, the paper towel has a dual purpose. First off, it helps absorb the urine, then it allows potty training. AS mentioned before, dogs will pee on the same spot over and over again until the odor is gone.
In order to prevent this from happening, the urine scent should be eliminated and enticing your pup with the pee-soaked paper towel, placing it to the designated pee zone so that they learn where they should do their business.
2) Pet Stains That Have Set
Now, for pet stains that already dried up and have already set deep into your carpet fibers, spotting the urine stains can be tricky.
You can use ultraviolet black light to spot in order to detect all the soiled areas. Then mark those areas with chalk.
If a blacklight is not available, then you can try these alternatives:
Once you find the soiled areas, clean it with a carpet cleaner. Don’t use steam cleaners since heat bonds the protein of urine to any human-made fiber which causes the stain and odor to permanently set.
After vacuuming the stains, treat these areas with enzymatic cleaners or your DIY solutions. However, if stains are still present, you can try using carpet stain removers available on your local grocery stores.
Once the carpet is dry, use a vacuum cleaner to remove cleaner residues such as baking soda.
Cleaning The Rugs
Carpets are not the only favorite pee zone for your pets. Rugs, too, had it rough. To clean up rugs, you can just place them in a washing machine. Add a pound of baking soda together with the detergent mixture in order to help remove the odor.
After a cleaning cycle in the washing machine, smell the rugs for traces of urine odor. If you can still smell it, put it back in the washing machine, and do another cycle. Only this time, wash them with an enzymatic cleaner to help break down the nasty urine odor.
via Vacuum Cleaners https://relentlesshome.com/how-to-get-dog-urine-smell-out-of-carpet/?utm_source=rss&utm_medium=rss&utm_campaign=how-to-get-dog-urine-smell-out-of-carpet
Shark is one of the favorite vacuum cleaner brands— mainly because they are powerful as Dyson-made cleaners but are pocket-friendlier.
However, like pretty much anything out there, Shark vacuum cleaners can sometimes malfunction and you will eventually run into small issues here, and there including a Shark vacuum won’t turn on.
Fortunately, there are fairly simple explanations and solutions, too.
What should you do when your Shark vacuum won’t turn on?
1) Power Plug
This is probably the simplest reason why Shark vacuum won’t turn on with the easiest solution. Most of the time, you just did not plug the vacuum cleaner into the outlet correctly.
So, check if the power plug is securely connected to the power outlet by wiggling the cord in order to check if the plug doesn’t fall off from the outlet. Otherwise, give the plug a push into the power outlet in order to secure it in place. Read Here: How to clean shark vacuum filter – A Step by Step Instruction
2) Vacuum Cord
If the vacuum still won’t turn on after, then you need to look at the cord itself, which might be cut or faulty. A damaged or faulty cord is common in the older vacuum cleaners with the damaged electrical wires inside the cord preventing power from getting to the vacuum cleaner.
Check the entire length of the vacuum cord for any cuts which can be stopping the electrical power from moving to the machine.
If you suspect an issue with the cord, then unplug the vacuum cleaner from the outlet in order to avoid fatal electrical shock. You can easily repair or replace a cord, depending on the extent of its damage.
3) Vacuum Switch
If the plug is securely connected to the outlet, the next thing you need to look at is the vacuum switch. AS obvious as it may seem, sometimes you need to check whether the switch is actually on.
If it’s on and the Shark vacuum still won’t turn on, then it could be a faulty switch that needs replacing.
4) Circuit Breaker
Vacuum cleaners are notorious for tripping circuit breakers. This is usually caused by electrical arcing that happens when electricity skips a gap between 2 conductors. Usually, these conductors are 2 pieces of exposed wires.
Arcing doesn’t usually trip a normal circuit breaker. However, it can easily trigger the AFCI (arc fault circuit interrupter), which is an advanced type of circuit breaker. If your vacuum cleaner has an AFCI, then it senses even the slightest sign of arcing in order to prevent dangers like electrical fires.
When powered, the vacuum cleaner will produce small sparks, which are tiny electrical arcs. As such, they can sometimes trip your AFCI circuit breaker and preventing the vacuum cleaner from turning on.
Whether you have a GFCI or AFCI outlet, you will need to check whether the breakers have tripped. If so, then the reset button on the outlet should have gone off. You can simply reset the breaker by pressing the reset button.
Now, if you have a normal outlet— doesn’t have a reset button— then you’ll have to check whether your home’s circuit breaker panel has tripped. If so, simply switch on the reset button. Read Here: 10 Best Vacuum for Hardwood Floors and Carpet
Tripping of the outlet breakers or circuit happens sometimes, however, if your Shark vacuum regularly trips the breaker, then it could be a sign of an electrical issue in the machine.
Some signs of electrical issues to check for include:
5) Suction Motor Thermostat
Some Shark vacuum cleaners like the Rotator model has a thermostat. This comes in handy in preventing the vacuum’s suction motor from the effects of excessive heat.
Vacuum cleaners are prone to overheating for various reasons.
Vacuuming while the dust canister is full not only reduces the efficiency of the vacuum but also lets excessive dirt into the inner parts of the machine.
This forces the motor to work harder leading to overheating. By emptying the bin regularly, you can minimize the risk of your vacuum cleaner overheating.
In addition, blockages in the brush bar, attachments, and hose can also prevent airflow and causes the motor to work harder. Clogged up or dirty filters can also have a similar effect on the vacuum cleaner.
Blockages in vacuum cleaners are especially common if you have pets that constantly shed their furs. Removing any blockages and cleaning or replacing clogged up or old filters can prevent overheating.
Now, when overheating, the thermostat shuts off the vacuum in order to let the motor cool down and prevent further damage from the excessive heat. You can get your vacuum cleaner back on by resetting the thermostat.
Here are the steps:
Vacuum cleaners have motors. And motors can eventually break down. No motor lasts forever. And they have lots of moving components which can also break over time.
If the problem of your Shark vacuum won’t turn on is the motor itself, then you’ll need to bring it to a professional for repairs. However, in most cases, if the motor already gave up, it is usually cheaper to just get a new Shark vacuum cleaner altogether.
via Vacuum Cleaners https://relentlesshome.com/shark-vacuum-wont-turn-on/?utm_source=rss&utm_medium=rss&utm_campaign=shark-vacuum-wont-turn-on
Get the best home decor ideas and product review, perfect home accents to celebrate your individuality from farmhouses bathrooms, dining rooms, DIY projects gardens storage ideas and more.